COE Eagles
  • HOME
  • SYSTEMS
    • FeedMaster
    • CTLMaster
    • SpaceMaster
    • MultiMaster
  • EQUIPMENT
    • In Stock Equipment
    • Coil Reels
    • Straighteners
    • Servo Feeders
    • Controls >
      • SyncMaster
      • Workroll Advisor
      • Servo and PLCs
    • Shears and Dies
    • Stackers
    • Washers
  • VIDEOS
    • COE Intro Video
    • NEW HD Servo Pilot Feeder
    • AHSS Video
    • Coil Processing Video
    • Cut-to-Length Video
    • Fineblanking Video
    • Roll Forming Video
  • SERVICE
    • 5-4-3 Warranty
    • Tech Support
    • Production Support
    • PM Support
    • Upgrades
    • Training
    • Spare Parts
  • NEWS
  • CONTACTS
    • Contact Us
    • Direct Sales
    • Dealer Sales
  • CAREERS
+1  (586)  979-4400

part  1:  Considerations  Particular  to  Coil  Stock

10/20/2015

 
Coil stock has become well established within the metalworking industry over the past few decades. There are numerous advantages processing coil stock including the fact that it:
  • Delivers sustained speed of production
  • Enables continuous press runs
  • Reduces material costs
  • Reduces scrap costs
  • Reduces storage space
  • Increases operating versatility
  • Enhances material availability
  • Removes the operator from point of operation
  • Improves the profitability of today’s metal stamper
Picture
​As positive as all of this is, however, there various material conditions unique to coil stock.  Understanding each of these potential issues and how to avoid or deal with them will help keep your operations at their best.  

Coil Set – all stock has, to some degree, a condition known as coil set, which is a curvature of the stock.  Since the stock is wound under tension, the coil set persists even as the material is unwound.  Coil stock straighteners are used to remove enough of the coil set to enable automatic feeding.  However, for more severe conditions, precision levelers may be required.

Crown – A curvature of the stock through its cross-section where the center of the stock is higher than the edges is known as the crown.  This condition can be reduced by the leveling process, but most often needs to be accommodated within the dies and coil equipment.  This requires abnormal clearances for the stock by recessing rolls or plates to allow passage of the edges of the stock while keeping pressure on the flat surface at the center of the stock.

Camber – This condition occurs when one edge of the material is longer than the other, and is most noticeable in narrow materials.  The material curves off to the side in one direction or even snakes back and forth.  Camber is measured in the number of inches (or fractions) of offset in a given length.  Once camber occurs, it is very difficult to keep on the center line of the tooling during the coil feeding process.  While this condition is best dealt with from the source of supply, the coil processing equipment and dies need to accept and accommodate the worst case conditions of camber.
​
Coil end kinks – Leading and trailing ends of coil stock can have significant “kink” in them, which must be removed to enable automatic coil handling and feeding.  This is commonly done with a knibbling device or a cropping shear in large, high production lines.  Other removal processes utilize coil breakers, debenders, or flatteners at the entry station of the power straightener.  However, a power straightener does not completely remove a coil end kink.  So, although the kinked coil can be fed through the die, it will most likely result in an unacceptable part.

Coil break – This results when coil material has a series of kinks or lines, typically evenly spaced, across the surface.  This condition cannot be completely corrected within the conventional coil processing line.  If not too severe, the coil break can be accommodated for within the system.  However, it will most likely result in unacceptable parts.
We’ll present more of the conditions that can negatively affect coil stock as well as solutions in our next blog post.

Comments are closed.

    Archives

    November 2018
    September 2018
    July 2018
    June 2018
    May 2018
    April 2018
    March 2018
    February 2018
    January 2018
    December 2017
    November 2017
    October 2017
    September 2017
    August 2017
    April 2017
    March 2017
    February 2017
    January 2017
    November 2016
    October 2016
    August 2016
    July 2016
    June 2016
    April 2016
    February 2016
    January 2016
    November 2015
    October 2015
    September 2015
    June 2015
    May 2015
    January 2015
    November 2014
    August 2014
    June 2014
    April 2014
    February 2014
    January 2014
    August 2013
    May 2013
    April 2013
    November 2012
    September 2012
    August 2012
    June 2012
    May 2012
    April 2012
    January 2012
    April 2011
    March 2011
    February 2011
    January 2011
    December 2010
    November 2010
    October 2010
    September 2010
    August 2010
    July 2010
    May 2010
    March 2010

    RSS Feed

HOME     SYSTEMS     EQUIPMENT     SERVICE     INTEL     REPS     CONTACT      CAREERS    TOUR      PRIVACY POLICY

in   two-minutes   Learn   why   coe   is   your   best   choice


ABOUT  US

Founded in 1976, COE Press Equipment designs and manufactures an extensive line of innovative coil processing solutions. Whether you need an individual piece of equipment, a completely integrated line, or a simple controls upgrade, COE can meet your requirements with the right equipment and service. COE provides one-stop capability starting with a top-notch engineering staff focused on R&D right through to fabrication, machining, assembly, electrical, quality control, start-up, service and 24/7/365 technical phone support. 

​We supply and service a wide variety of global markets and industries including automotive, appliance, lighting, metal processing, housewares, lawn and garden, contract stampers, tool and die builders, and many others.
COE PRESS EQUIPMENT
40549 Brentwood
Sterling Heights, MI 48310
+01 (586) 979-4400
Picture

© COE PRESS EQUIPMENT. All rights reserved. Some COE products, such as straighteners are Patent Pending.
​Privacy Policy. Designed by
 Industry-Scope.com and Powered by Spud Software
Picture
Picture
HOME      SYSTEMS      EQUIPMENT      SERVICE      TOUR      INTEL     REPS     CONTACT

NEWSLETTER SIGN-UP
ENGLISH       ESPANOL
COE PRESS EQUIPMENT
40549 Brentwood
Sterling Heights, MI 48310

+! (586) 979-4400
Picture
© 2015 COE PRESS EQUIPMENT. All rights reserved. Designed by Industry-Scope.com and Powered by Spud Software

share

COE Eagles